-
Posts
247 -
Joined
-
Last visited
Information
-
Aircraft
J230
-
Location
Townsville (Donnington)
-
Country
Australia
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
corvairkr's Achievements
Well-known member (3/3)
-
corvairkr started following Another Jab down 29 Feb 2020. , Move over ROTAX... , On J230, the heat, and suitability of the Rotax 912ULS and 3 others
-
corvairkr changed their profile photo
-
The Jab in the link is a 912 conversion. 😊 jason
-
RF maybe you could speak to Ole at Australian aircraft kits. I believe he did the tidy conversion posted by pylon 500 in this thread. Jason
-
Tensile strength of Hoop Pine?
corvairkr replied to duncan_rtfm's topic in Aircraft Building and Design Discussion
Here are some specs compared to Douglas fir. https://boatcraft.com.au/informationpages/pdfs/HoopPine-DouglasFirComparison.pdf jason -
Vans RV-7 crash, S of Charters Towers 23/04/2021
corvairkr replied to onetrack's topic in Aircraft Incidents and Accidents
https://www.atsb.gov.au/publications/investigation_reports/2021/aair/ao-2021-017/ -
Bill, when I had my Xair I got my tyres from here Trailer Parts | Garbutt | NQ Wheels & Castor Supplies I tended to pick up a few goat heads so got the heavier tread. They worked very well. Jason
-
Another Jab down 29 Feb 2020.
corvairkr replied to BirdDog's topic in Aircraft Incidents and Accidents
https://www.raa.asn.au/safety/accident-and-defect-summaries/ jason -
Remembering my little mate
corvairkr replied to alf jessup's topic in Aircraft Incidents and Accidents
4 years, Alf. Not a day I’ll forget in a hurry. jason -
G’day Brett, I’ll lay money on your problem being your ducting to your radiator not allowing enough airflow. i’ve recently had to mount my radiator vertically on the engine mount near the Firewall on my 601 HDS and had the same problem. I originally had a Plenum over the radiator fed by various inlets but eventually had to make a NACA duct feeding directly to the face of the radiator to allow effective ground cooling. It now runs waaay to cool but that’s a simple fix with some Aluminium tape. Jason
-
Man walks away after plane crash landing in Ingham
corvairkr replied to farri's topic in Aircraft Incidents and Accidents
No. On his way South from Innisfail to Dysart. Landed at Ingham due to Weather and crashed it whilst landing. Jason -
Man walks away after plane crash landing in Ingham
corvairkr replied to farri's topic in Aircraft Incidents and Accidents
That link was back in 2014. There was a Storch that flipped on landing a couple of days ago though. Jason -
Skippy, have you got a close up photo of the Staining ? If the Chemicals you have tried have had little effect, I would start doing test spots starting with a light Polish/Pad Combo gradually moving up to a heavy Compound and even Wet Sanding if required. Sometimes there just isn’t enough Paint to remove the defects and repainting is the only option. It would probably be easier and cheaper for you to get a GOOD local Detailer to have a look at it for you ( I may know someone in your area ) For protection you can’t go past a good quality Professionally applied Ceramic Coating although there are consumer grade coatings available prep is key to a good result. Jason
-
Avionics wire
corvairkr replied to BackcountryAeropup's topic in Instruments, Radios and Electronics
ASAP at Caboolture have Tefzel wire and are really good to deal with. http://www.asapspares.com.au/ jason -
AOPA and RAAus in Dispute over Slogan - Australian Flying Jason
-
Zenith engine failure at Gatton
corvairkr replied to derekliston's topic in Aircraft Incidents and Accidents
Check the third one down, Derek. Accident and defect summaries - RAAus Jason