Jump to content

BC0979

Members
  • Posts

    58
  • Joined

  • Last visited

Posts posted by BC0979

  1. 1 hour ago, Area-51 said:

    Buy new doors, cut off upper windows; 1/2 doors done 🤷🏼‍♂️

    Understood, but what about the hinge/mounting points? And air flow on the upper half? Sure some sort of fairing is needed on the upper half which is why I am asking this forum

     

  2. Great input Guys!

    I have bare aluminum (no paint) under the VGs.

    I did see that the StolSpeed website offers double sided tape but as stated earlier, not the right size for ICP VGs.

    I did not see that the "manual" recommended super glue. 

    If  I use super glue, I could remove the VG with a heat gun if and when a replacement is required.

    • Like 1
  3. Thanks to all of you I am almost there....😁

    After I get my Savannah S assembled at the field, I will install the little plastic VG pieces. I didn't want to transport the wing with them installed to prevent possible damage.

     

    So the question is, what do I use to install these little plastic VG pieces? Is there a clear glue the you recommend?

     

     

    • Like 1
  4. Yes, I am in Florida, USA so FlyBoy is correct. I am required to have 7" minimum ground clearance.

    15X6-6 tire deflated plus the bottoming out of the nose gear to the stops. I will need to check this.

    I fly off a grass field so nothing will save me if I bury the nose gear in a gopher hole....

    Thanks again for all the input.

    • Like 3
  5. I also read the Stolspeed.com prop study that you all suggested.

    That guy does get work. His study uncovered that the cruise speed remains essentially the same for all props he tested but climb rate would be affected from going down to a 68 from a 71. I can live with the that since I this is not a Stol competition plane

    • Like 2
  6. I truly appreciate all the input.

    I acknowledge that I am installing a non-rotax engine and the elevation of the prop shaft may be different.

    I understand the ramifications of raising up just the nose gear.

    I contacted a guy that purchased all three Savannah S kits which included the 912 and prop. ICP sold him a 175cm(68.9") prop.

    I received 180cm(70.9") which yields 3.5" of ground clearance.

    If I convert to 22" tires(all three) from the 15" tires that would yield another 3.5" and bankrupt me at the same time 😂

     

    • Like 1
    • Haha 1
  7. Hello to all...

    What prop diameters are you turning? And do you have the required minimum 7" ground clearance with the 15x6-6 tires?

     

    I just mounted my prop and discovered that I only have 3.5" of ground clearance. I think I have the wrong prop. The nose fork will not accommodate a taller tire.

     

    20240121_101445.thumb.jpg.810d85c7ef0bf68ad380b24c7f401eba.jpg

     

     

  8. Bodie

    Thanks for the pics. They are very helpful.

    No I have not installed the extensions as yet, been wrestling with it, then I get frustrated and stop.

    The roof also has me puzzled as to why the pre drilled holes are at the wing skin edge and the precut lexan overlaps so much. The construction manual has been very helpful...LOL

  9. Before I go hacking on these miscellaneous parts I thought it wise to ask ....

    Is there a trick to installing these two skin extensions?

    The blue tape, so I don't scratch my lexan. I know that there is a rubber edge trim that was supplied.

    20231211_125703.thumb.jpg.79a0ad148780eeac33c9e0a5d5af4efc.jpg

     

    Then there's the roof panel. The prepunched holes are quite a ways in from the edge. Flutter issue in the making?

    20231211_125734.thumb.jpg.4bd8b7ca88847b30a95dfc7b940d6e15.jpg20231211_125726.thumb.jpg.81497624edf02271ab8492e3e7cd37a4.jpg

     

    Any insight would be greatly appreciated

    Bryan

  10. I downloaded the maintenance manual as you suggested.

    Thank you, thank you

    Very difficult to find things on their website 😕

    The person that made the construction manual must have done the website too LOL

    I removed the 20mm long machine screw/dip stick and syringed the excess out

    😁

    • Like 4
  11. Ahhh.. reservoir

    This is the first time for me with his type of cylinder.

    My other plane had closed, non reservoir cylinders with bleeders so you could pressure bleed from either end. I did not see any info on my construction manual on the air space and did not know about registration either.

    Apparently there isn't any issue with our park brake located above the toe brake cylinders cuz I would think gravity would cause the fluid to drain down to the toe brakes and eventually empty out/bleed off.

    I quess I should use a syringe and remove a few CC's and make a 20mm dip stick,LOL

     

    Thank you all for the insight

     

     

    • Like 2
  12. Just filled my brake lines with Shimano brake fluid which is mineral based and was recommended by my dealer.

    Got all the connector leaks stopped except for the very top of both cylinders.🤨

    The bleed Allen screw is as tight as I can get it. It is so tight that it will rotate the top plate of the cylinder.

    Maybe it takes time for the top seal to expand from the newly installed mineral oil?

     

  13. Would someone help me out by sending me pictures of the jury strut installed on the Savannah S.

    The "manual' is not helping, 😂

     

    I am more familiar with round tubes for the jury struts, the S has a formed aluminum strut SA202/203, SN451/452 bracket mounted on the wing bottom, and SN450 which is "wrapped around" the strut?

    Uncertain about using rivet nuts and screws to secure as opposed to pins (better shear strength)

     

    THANK YOU

    Bryan 

     

×
×
  • Create New...