Trackley

Hi Anyone have any more info on this?

Ok so called rotax spoke with Gary. The clearence i have is about 2mm on the right side of the cowl. Gary said that should not be a problem. I have just run the engine today with the spinner on with no problems. But boy talk about fine tolerances

Call bolly, I think they do some extensions.

Most VG I have seen didnt need any spacers and they had bolly props

Hi guys im at a road block with my brand new Bolly prop, does anyone know of a extension that can be bolted onto a rotax 912 uls prop thrust plate to extend out another inch or so, so i can have adequate clearance of the spinner backing plate of my new Bolly prop and spinner.

Cool alright. I have just bought a new bolly and awaiting arrival.

where is the brake fluid reservoir for the toe brakes?

Is there anyone out there.

Hi guys can i adjust (tilt forward) the rudder pedals on my vg for more comfort with my L1 or is it part of the flight controls. Left for an L2?

you can also buy a compass knife at places like lincraft etc then cut your own rings with coloured contactI purchased one to use on my X-Air ASI and its easy to cut the outer ring then reduce the compass dia 3mm then cut again.... too easy :)

[ATTACH=full]45910[/ATTACH]

 

Pete

No worries Neil thanks for the advice.

trackley know john Gordon tell him dingo is still lost neil

Hi guys. I have a 19 reg savannah vg and want to make a inspection flap on a hinge to open and check my oil.hi trackley personally I would not put a little inspection flap in BECAUSE

by removing the top cover completely you can see the whole of your motor and them bloody birds and rats have been known to build a home there very quickly

 

plus better inspection of oil leaks plug wires broken exhaust springs

 

yes I know its a pain in the **** to remove the cover but visual inspection is best neil

Hi TrackleyI made an oil filler check panel for my VG. Was really worthwhile. I'll be down the hangar today and take some pics.

 

Peter

Hi TrackleyHave a look at Tony Spicers web site for his Panther in the Fibreglass section. He has a few step by step photos how he made an inspection hatch in the cowl.

 

https://get.google.com/albumarchive/116494848541088965116

Hi guys. I have a 19 reg savannah vg and want to make a inspection flap on a hinge to open and check my oil. How and or where so i start. I know i have to cut out a hole. Probability sounds silly but yeah. Anyone that has done this how do i go about it. Where do i get the fastners from how do i make a seat for it to sit on?

Regards

Trackley,Sorry mate I looked in the box today and there were no spare ones, maybe Scott's idea is worth trying, hope you get it sorted mate..

David

Trackley:As an alternative, you can do what I did when I built my Nynja.

 

I got some different coloured "hookup" wire and used a piece of stiff wire with different colored insulation and glued it around the ring of my ASI

 

.[ATTACH=full]45763[/ATTACH]

Sweet David much appreciated. I will have my fingers crossed for you and me.

I know this was mentioned here just recently. But I am at wits end trying to find some green and yellow arc stickers to go onto my Savannah VG ASI. I have found 2 companys in America and Germany but want like $45 for postage of a 10 dollar sticker. What can I do.

there is one in mackay mate at palmyra, Matts Flying School, I did my ticket there.Its a Savannah S, last i heard, 150/hr wet solo, 190 dual.

Hi Guys

Just putting this out there, what sort of price would I be looking at to land a Nynja kit with 100hp to my front door?

Im Picking up something else about Savannah's is that the owners are a good bunch of blokes too.

Hi I do hope this is not to personal for this site, but I am a low hour pilot very keen on owning my very own Savannah.

I am trying to find someone that owns a Savannah and that would kindly like to take me up for a test flight and a good run over the aircraft, before I start spending money on purchase's and the like.

I'm based in Emerald CQ.

Regards Travis

Hi Names Travis, I have been out of the game for 8 years and just have recently got back in the seat. Yes I have my RA but just needing my nav to complete.

I have my eyes on a Savannah VG for sale at Mitchel, I'm from Emerald QLD. Flying is my true passion in life and I cant wait to own my own. BTW I grew up just north of Springsure on "Aldebaran"

Just checking in to say G'day from one enthusiast to the next.

Looking to purchase my first RA aircraft.